Question 1

What is the function and application scope of a water softener?

Accepted Answer

A water softener removes hardness ions (mainly calcium and magnesium) from water through ion exchange, preventing scale formation in pipes and equipment.

Question 2

What is the peak flow rate?

Accepted Answer

The peak flow rate is 400 to 500 L/h for short periods such as filling a bathtub or running multiple taps. Sustained use above 300 L/h may cause hardness leakage.

Question 3

Does the system run continuously at 300 L/h?

Accepted Answer

No. 300 L/h is the maximum continuous treatment rate. The actual flow depends on your water demand. The softener only treats water as it is used.

Question 4

Can I draw more than 300 L/h for a short time?

Accepted Answer

Yes up to approximately 450 L/h for 5 to 10 minutes. However doing this regularly will reduce soft water quality increase pressure drop and shorten resin life.

Question 5

What inlet water pressure is required to achieve 300 L/h output

Accepted Answer

Minimum 2 bar or 30 psi at the inlet. For stable 300 L/h output the recommended pressure is 2.5 to 4 bar or 36 to 58 psi. Below 1.5 bar the flow rate will drop significantly.

Question 6

How much salt does this 300 L/h system use

Accepted Answer

Approximately 2 to 3 kg of salt per regeneration. If you use 300 L/h for 4 hours per day or 1200 L per day salt consumption is about 15 to 25 kg per week. Check the salt level every 1 to 2 weeks.

Question 7

How long can the system produce 300 L/h before the resin wears out

Accepted Answer

Resin typically lasts 3 to 5 years under normal conditions with chlorine below 1 ppm and iron below 0.3 ppm. After that the softener will still run but hardness removal efficiency drops.

Question 8

What happens if I use more than 300 L/h continuously

Accepted Answer

You will experience hard water slip which means some hardness passes through. You will also see higher pressure drop and faster resin exhaustion. If you regularly need more than 300 L/h consider a larger model such as 500 L/h or 1000 L/h.

Question 9

My flow rate is less than 300 L/h. What is wrong

Accepted Answer

Possible causes include a clogged pre filter low inlet pressure below 2 bar a plugged distributor or resin fouled with iron or silt. Also check if the bypass valve is partially open.

Question 10

How is this 300 L per hour model different from a 300 liter resin volume softener

Accepted Answer

A 300 L/h model refers to flow rate and is for small home or cafe use with about 25 to 50 liters of resin. A 300 liter resin model is for large commercial or industrial use with a much larger tank and 80 to 150 kg of salt per regeneration. Make sure you order the correct type for your needs.

Question 11

Does the 300 L/h softener need electricity to produce water

Accepted Answer

No. The softener can produce water without power because water flows through the resin. However regeneration requires electricity to move the automatic valve. If power is out the resin will eventually exhaust and you will get hard water until power returns.

Question 12

Can I adjust the 300 L/h limit

Accepted Answer

No. 300 L/h is a physical limit of the valve body and piping. You cannot increase it via programming. If you need more flow you must install a larger softener in parallel or upgrade the unit.

Question 13

How do I set the regeneration schedule for my 300 L/h usage pattern

Accepted Answer

Use meter initialized mode. First program your water hardness such as 300 mg per liter. Then program your resin capacity based on your small tank. The valve will auto calculate how many liters can be treated before regeneration. At 300 L/h continuous use that might be 20 hours of runtime. In real life the valve will trigger regeneration after 2 to 4 days of normal use.

Question 14

What is the minimum pressure needed for 300 L/h

Accepted Answer

2 bar or 30 psi.

Product profile

Customization

Certification

Salt Rejection Rate

Model NO.

Application

Capacity

Tank Material

Filter Media

Technology

Product Name

Operation

Resin Volume

Tank Diameter

Tank Height

Control Valve

Transport Package

Specification

Trademark

Origin

HS Code

Production Capacity

Key features

Company profile

About Our Factory & Business Background

Our Production Capability & Technical Expertise

Our Industry Experience & Global Business Record

Product Q&A

Send Inquiry

You may also like